As a PC/ABS resin supplier, I get this question all the time: “What is the elongation at break of PC/ABS resin?” It’s a smart one too—because elongation at break isn’t just a number on a spec sheet. It’s what tells you if a resin can handle the stress of real-world use: the minor dents from shipping, the vibrations of a moving component, the small impacts that would crack a brittle material. I’ve talked to engineers who’ve had a part fail prematurely because they picked a resin with too low an elongation value, and others who overspec’d it, adding unnecessary cost. So let’s break this down straight, no jargon overload, from someone who mixes and ships this resin every week. PC/ABS Resin

First, let’s define elongation at break in simple terms. When you pull a material until it snaps, the elongation at break is the percentage of its original length it stretched right before breaking. If a 10-inch long PC/ABS sample stretches to 13 inches before breaking, its elongation is 30%. Higher numbers mean the material is more flexible and tough—it can bend or stretch a little instead of shattering.
PC/ABS is a blend of polycarbonate (PC) and acrylonitrile butadiene styrene (ABS), so its elongation at break isn’t a fixed value. It depends on how much PC or ABS is in the mix, the additives we add during processing, the temperature it’s tested at, and even the thickness of the molded part. That’s why as a supplier, I never give a single, one-size-fits-all number—instead, I work with customers to match their specific application.
Let’s start with the base resin ratios. Pure PC has a high elongation at break, usually between 110% and 120%. That’s why it’s so tough for things like safety goggles and impact-resistant parts. Pure ABS, on the other hand, has lower elongation, typically between 20% and 40%—it’s stiffer, good for things like toy bodies or electronic housings that don’t need to bend much. When we blend them for PC/ABS, we balance stiffness and toughness.
If you want a high-toughness PC/ABS for parts that will see rough handling, we blend more PC. That gives elongation at break values between 60% and 100%. This is ideal for automotive bumpers, power tool casings, or consumer electronics that might get dropped. Last quarter, a customer in the power tool industry came to us because their previous resin was cracking when the tool fell off a workbench. We switched them to our high-PC PC/ABS, and their failure rate dropped from 8% to under 1%—that’s the difference the right elongation number makes.
For applications that need a mix of toughness and dimensional stability—like computer cases, medical device housings, or appliance parts—we use a 50/50 or similar balanced blend. These have elongation at break values between 30% and 60%. This range is versatile: it’s flexible enough to handle minor assembly stresses (like snapping parts together) but stiff enough to keep its shape over time. I had a customer making laptop chassis a few years back who tried a pure ABS blend; their chassis would warp when they attached the screen hinges. The balanced PC/ABS we supply doesn’t warp, and it has enough elongation to withstand the repeated opening and closing of the laptop.
Now, additives play a big role too. Flame retardant (FR) additives are common in PC/ABS for electronics and automotive parts, but some FR packages can lower elongation at break. A standard non-FR PC/ABS might have 50% elongation, but adding a standard halogenated FR can drop that to 35% to 45%. However, we have custom FR blends that maintain higher elongation—our halogen-free FR PC/ABS, for example, stays around 40% to 50% elongation, which is crucial for medical parts that need to meet fire safety standards but also need to flex during assembly. Other additives, like impact modifiers, can boost elongation even further for extreme applications—we offer a modified PC/ABS with elongation up to 110% for parts that handle heavy impacts, like construction equipment components.
Testing conditions matter more than most people realize. Elongation at break is always tested according to ASTM D638 or ISO 527 standards, but those tests are done at 23°C (73°F) with a specific specimen thickness (usually 3.2 mm). If a customer is molding a thin part (like a 1 mm thick smartphone bezel), its actual elongation in use might be lower than the test number because thinner parts are stiffer. Conversely, thick parts might have higher elongation because they have less internal stress from molding. Temperature also affects it: at low temperatures (like -40°C), PC/ABS becomes stiffer, and elongation at break drops—often by half. For parts used in cold environments, like outdoor agricultural equipment, we adjust the blend to add low-temperature impact modifiers, so the elongation at break stays above 20% even at -40°C.
So how do we measure this accurately as a supplier? Every batch of PC/ABS we produce goes through quality testing. We pull specimens from each production run, condition them to standard temperature and humidity, and run elongation tests. We keep records of every test, so customers can request batch-specific spec sheets with their exact elongation number. That’s a service I’m proud to offer—no vague “up to X%” numbers, just hard, testable data.
Now, common mistakes I see customers make: either picking a resin with too low elongation and dealing with part failures, or picking one with too high elongation and wasting money. For example, a automotive lighting manufacturer once ordered a high-toughness PC/ABS (80% elongation) for a turn signal housing. The part worked fine, but it cost 20% more than the balanced blend they needed. Their turn signal only needed to handle minor vibrations, so a 45% elongation blend would have been perfect. On the flip side, a customer making electrical connectors tried to save money with a low-elongation ABS blend. Their connectors cracked when the wiring was bent during assembly, leading to field failures. The balanced PC/ABS (40% elongation) we suggested fixed that issue without adding extra cost.
Another use case for high elongation PC/ABS is flexible parts that need to snap back into shape, like toy hinges or grip components. A toy company I work with uses our 65% elongation PC/ABS for action figure joints— it bends with play without breaking, and it’s durable enough to last through thousands of plays. For parts that are glued or welded, elongation also matters: if a part is too brittle, the weld joint will crack; if it’s too flexible, the joint won’t hold. Our balanced blend hits that sweet spot for welding applications.
If you’re working on a project and aren’t sure what elongation at break you need, here’s a quick guide. For low-stress parts (decorative trims, cabinet panels): 20-30% elongation. For moderate stress (electronic housings, appliance parts): 30-60% elongation. For high stress (automotive bumpers, power tools, impact-resistant components): 60-110% elongation. Always consider the environment too: cold weather needs a bit higher elongation to account for brittleness, thin parts might need a higher number than thick parts, and flame retardant needs might require adjusting the blend to keep elongation up.
As a PC/ABS supplier, our goal isn’t just to ship resin—it’s to help you pick the right resin for your application. If you’re struggling with part failures, overspending on materials, or just trying to nail down the right elongation at break for your project, I’m here to help. We can provide sample testing, custom blend adjustments, and detailed technical specs to make sure your parts work the way they’re supposed to, every time.

Don’t guess at your resin needs—reach out to our team to discuss your project requirements, and we’ll help you find the perfect PC/ABS resin with the right elongation at break and other properties to fit your application.
PBT Resin References
- ASTM International. (2022). Standard Test Method for Tensile Properties of Plastics (ASTM D638).
- ISO. (2019). Plastics – Determination of tensile properties (ISO 527).
- Olejnik, O., et al. (2020). “Toughness and Elongation Behavior of PC/ABS Blends with Different Impact Modifiers.” Journal of Applied Polymer Science, 137(22), 48752.
- Gahleitner, M., et al. (2018). “Effect of Flame Retardants on Tensile Properties of PC/ABS Blends.” Polymer Engineering and Science, 58(10), 1892-1900.
- Modern Plastics Encyclopedia. (2021). “PC/ABS Blends: Properties and Applications.” McGraw-Hill.
Jiangsu Kingsder New Material Technology Co., Ltd.
Jiangsu Kingsder New Material Technology Co., Ltd. is one of the most experienced pc/abs resin manufacturers and suppliers in China, also accepts customized orders. Please rest assured to wholesale UL recognized pc/abs resin in stock here from our factory. If you have any enquiry about quotation and free sample, please feel free to email us.
Address: No.426-2 Kunjia Road, Kunshan Development Zone, Kunshan City, Suzhou City, Jiangsu Province, P.R.China
E-mail: chloe@kingsder.com
WebSite: https://www.kingsderplastic.com/